by

Overhead Door Model 55b Remote



Purchase an Overhead Door remote control online and SAVE. Overhead Door Code Dodger remote control. IF YOU ORDER THIS PRODUCT, IT WILL BE SUBSTITUTED WITH PART # 37517R (REMOTE CONTROL, CD #37517R - FREE SHIPPING). THIS REMOTE CONTROL HAS BEEN DISCONTIUNED AND IS NO LONGER AVAILABLE. This model remote control was the standard remote control. Overhead Door Garage Door Opener Remote OCDTR-3BX Three Button CodeDoger. Overhead Door Remote Control 109130-390 Two Button. Overhead Door Brand - Model OKP-BX Wireless Keypad Garage Opener - White. Overhead Door O3T-BX Garage Door Opener Remote, 3 Buttons, Key Chain or Visor.

  1. Overhead Door Model 55b Parts
  2. Overhead Door Model 55b Remote Keyless
  3. Overhead Door Model 55b Remotes

All garage door remotes operate in one of two ways shown below.

Dip Switches- The original 'old style pre 1992' garage door remotes have dip switches that are found in the battery compartment of the remote. Dip switches are the little toggle switches (pictured left) that can be set in the up or down position and must MATCH the corresponding dip switches found on your overhead motor or attached receiver box. No dip switches, and made after 1980 means rolling code! The second most important part is the frequency, it is found on the back of your remote and is labeled 300mhz, 310mhz, 318mhz for example, if it's worn off then shop by brand name.

Rolling Code - The second type of remote 'post 1992' is the rolling code remote which uses a LEARN button instead of dip switches. Meaning, there won't be any dip switches in the battery compartment of your remote. On the overhead motor or gate receiver box, there will be a LEARN button that is pressed in order to program your remote to it. The last part is the frequency, 390mhz and 315mhz are the most common and are found on the back of your remote, if it's worn off then shop by brand name.

Remote

Shop for remotes by the number of dip switches or by rolling code, then by frequency.

Programming your Overhead Door Codedodger® wireless keypad. Should you need additional information please contact our customer service department at 1-800-275-6187.

Resetting your keypad:

If, at any time, during programming, you should enter the wrong PIN or make a mistake, you should reset the keypad to its factory setting.

Model

  1. Open the keypad cover half way

  2. Press and hold the number 8 and the PROG buttons while opening cover fully.

  3. The indicator light will blink once and go out.

  4. Close the cover. Http://fbspy.com. You are now ready to re-program your keypad.


Basic Programming:

  1. Open cover fully - Indicator will blink once on go out

  2. Press 3-5-7

  3. Press PROG - Indicator will blink once per second

  4. Enter PIN 1 (up to 8 digits)

  5. Press PROG - Indicator will blink twice per second

  6. Close cover. Your keypad is now ready to be programmed to the garage door opener.

    Locate the Learn code button on your Codedodger garage door opener.

    TOYOTA N-TD20 Towing tractor. Spare parts catalog. Service Manual. 6353658 N-02-TD25 TOYOTA N-02-TD25 Towing tractor. Spare parts catalog. Service Manual. 6353659 N-TD25 TOYOTA N-TD25 Towing tractor. Spare parts catalog. Service Manual. 6353660 TB12 TOYOTA TB12 Towing tractor. Spare parts catalog. Service Manual. 6353661 20-TB12. Toyota td25 manual From warranties on Toyota replacement parts to details on features, Toyota Owners manuals help you find everything you need to know about your vehicle, all in one place. Detailed Toyota manuals and Toyota warranty information help with questions about your vehicle specifications and maintenance schedules. Toyota continue to enhance the Towing Tractor technology through valuable feedback from the airport industry and operators. For example, the 42-2TD25 towing tractor with the larger 3.5 litre engine was developed by Toyota engineers in conjunction with feedback from the Australian airline industry.

    Depending on model, the learn code button will be located under the light cover or on the rear panel.


Basic Opener Programming:

  1. Press the learn code button - Learn code LED will flash

  2. Open cover on keypad fully

  3. Enter PIN number

  4. Press the SEND button 4 times, or until the door begins to operate.

  5. You will now be able to use your wireless keypad normally.


Controlling a single door with your keypad:

  1. Open keypad fully

  2. Press PIN number

  3. Press SEND once

  4. Door should operate normally

    Note: As a “panic” feature this keypad will operate door for up to 30 seconds from any button.

Overhead Door Model 55b Remote


Programming multiple doors with your keypad:

Overhead Door Model 55b Parts

Program your keypad according to the steps outlined in the Basic programming section listed above.

  1. Open cover fully Phillies font free.

  2. Enter PIN number

  3. Press PROG - Indicator will blink once per second

  4. Press PROG - Indicator will blink twice per second

  5. Press PROG - Indicator will blink three times per second

  6. Enter the total number of doors (2 or 3)

  7. Press PROG

  8. Close cover

  9. Your keypad is now ready to be program to the garage door openers.

  10. Locate the learn code button on your garage door openers

  11. Press the learn code button once - Learn code indicator will flash

  12. Open cover on keypad fully

  13. Enter PIN

  14. Press SEND

  15. Enter door number 1-2-or-3

  16. Press send button 4 times, or until door operates

  17. Repeat these steps for door 2 and 3


Controlling multiple doors:

  1. Open cover fully

  2. Enter PIN number

  3. Press SEND

  4. Enter door number (1-2-or 3)

  5. Chosen door should operate


Adding PIN 2:

  1. Open cover fully

  2. Enter 1-5-9

  3. Press PROG - Indicator will blink once per second

  4. Enter PIN 2 (up to 8 digits)

  5. Press PROG Indicator will go out

  6. Close cover. Your keypad is now ready to be programmed to the garage door opener.

  7. See steps in Basic programming.


Adding temporary PIN:

  1. Open cover fully

  2. Enter PIN 1

  3. Press PROG - Indicator will blink once per second

  4. Press PROG - Indicator will blink twice per second

  5. Enter temporary PIN

  6. Press PROG - Indicator will blink three times per second

  7. Close cover. Your keypad is now ready to be programmed to the garage door opener.

  8. See steps in Basic programming.


Canceling the temporary PIN:

The temporary PIN will remain active until PIN 1 is entered.

Overhead Door Model 55b Remote Keyless


Changing a PIN:

Overhead Door Model 55b Remotes

  1. Open cover fully

  2. Enter PIN to be changed

  3. Press PROG Indicator will blink once per second

  4. Enter new PIN

  5. Press PROG

  6. Indicator will blink twice if PIN 1 has changed or go out if PIN 2 was changed

  7. Close cover. Your keypad is now ready to be programmed to the garage door opener.

    Locate the Learn code button on your Codedodger garage door opener.

    Depending on model, the learn code button will be located under the light cover or on the rear panel.